+44 20 3290 1099
Contact

DAM-B-72 AC Universal Ampermeter

The device can be used in electrical panels, laboratories, and test devices. With the assistance of a current transformer, it measures the AC passing through the system in terms of Amper unite. If the current exceeds the adjusted current then the alarm led started to blink after the the adjusted time delay changes the output position. When the current exceeds the adjusted current value the device starts to count for the adjusted delay time and after that, it opens its output contacts. After energizing the device, a “dA -b “ message appears on its screen for 2seconds and then it starts to show the current value.

■ The current transformer ratio can be adjusted between 5/5 and 10000/5 using the touch buttons on the front panel of the device.

■ Stores the maximum demand value and the peak value on its memory and keeps these values even if the energy supply goes off.

■ When the measured value of the seconder current reaches 5,1 A, “ OvEr” the message starts to flash on the screen to warn the user that the value of the current exceeded the limit values.

Category: Tag:

Description

DAM-B-72 AC Universal Ampermeter

General Informations

The device can be used in electrical panels, laboratories, and test devices. With the assistance of a current transformer, it measures the AC passing through the system in terms of Amper unite. If the current exceeds the adjusted current then the alarm led started to blink after the the adjusted time delay changes the output position. When the current exceeds the adjusted current value the device starts to count for the adjusted delay time and after that, it opens its output contacts. After energizing the device, a “dA -b “ message appears on its screen for 2seconds and then it starts to show the current value.

■ The current transformer ratio can be adjusted between 5/5 and 10000/5 using the touch buttons on the front panel of the device.

■ Stores the maximum demand value and the peak value on its memory and keeps these values even if the energy supply goes off.

■ When the measured value of the seconder current reaches 5,1 A, “ OvEr” the message starts to flash on the screen to warn the user that the value of the current exceeded the limit values.

Technical Data

Relay output 1
Current Ttransformer 5-10000 Ampere Ok
Directly Current Ttransformer 2-100 Ampere No
Over Current Can Be Set 1
Under Current Can Be Set No
DEMAND Ok
RS485 – MODBUS RTU RS485, Modbus – Rtu No
Frequency 50-60 Hz
Ambient temperature -5 C….+50 C
Storage temperature -20 C….+70 C
Supply voltage 230 Vac
Dimensions 72x72x80 mm
Quantity in 1 box 10

 

Operational Voltage (Un) : 230Vac

Operating range : (0,8-1,1) x Un

Frequency : 50/60 Hz

Power Consumption : < 4VA

Measurement Sensitivity : %1 +1 digit

Current Transformer Ratio : 5/5……….10000/5 A

Display : 4 Digits Led Display

Contact Current : Max. 3A / 240Vac

Protection Class : IP 20

Terminal Protection Class : IP 00

Operating Temperature : – 5 °C …. + 50 °C

Operating Humidity : %15 …… %95

(without condensation)

Installation : to the panel tap

Dimensions :DAM – B – 96 ( 96x96x80 mm)

: DAM – B– 72 ( 72x72x80 mm)

: DAM – B – 48 ( 48x48x50 mm)

Related Products

The device can be used in electrical panels, laboratories, and test devices. With the assistance of a current transformer, it measures the AC passing through the system in terms of the Amper unit. When the current exceeds the adjusted over current or goes below the adjusted under current values the device starts to count for the adjusted delay time and after that, it changes Re1 or Re2 outputs contact position. After energizing the device, “dA -c “ the message appears on its screen for 2 seconds and then it starts to show the current value.

■ The current transformer ratio can be adjusted between 5/5 and 10000/5 using the touch buttons on the front panel of the device.

■ Stores the maximum demand value and the peak value on its memory and keeps these values even if the energy supply goes off.

■ When the measured value of the seconder current reaches 5,1 A, “ OvEr” the message starts to flash on the screen to warn the user that the value of the current exceeded the limit values

6+1

DAM-C-72 AC Universal Ampermeter

Read more

The device can be used in electrical panels, laboratories, and test devices.With the assistance of a current transformer, it measures the AC passing through the system in terms of the Amper unit. Two over the current set ( SP1, SP2 ) with a different output contact for each. The first set value is SP2, the higher one is SP1. When the current exceeds the adjusted first over currentvalue (SP2) then the alarm1 led will start to blink and after the set delay time, the device would change the possession of the Re2 output contact.If the current exceeds the higher current value the device opens its 1st output too. The current is called normal if it is below these two limits. After energizing the device, the “dA -d “ message appears on its screen for 2 seconds, and then it starts to show the current value. Even when the power supply is off, the stored values will not be deleted.

■ When the measured value of the seconder current reaches 5,1 A, “ OvEr” the message starts to flash on the screen to warn the user that the value of the current exceeded the limit values.

7+1

DAM-D-96 AC Universal Ampermeter

Read more

The device can be used in electrical panels, laboratories, and test devices. Withthe assistance of a current transformer, it measures the AC passingthrough the system in terms of Amper unite. After energizing the device“dA -A “ message appears on its screen for 2 seconds and then it starts toshow the current value

■ The current transformer ratio can be adjusted between 5/5 and 10000/5 usingthe touch buttons on the front panel of the device.

■ Stores the maximum demand value and the peak value on its memory andkeeps these values even if the energy supply goes off.

■ When the measured value of the seconder current reaches 5,1 A, “ OvEr”the message starts to flash on the screen to warn the user that the value of thecurrent exceeded the limit values.

2+1

DAM-A-72 AC Universal Ampermeter

Read more
DAK-72 Direct AC Ampermeter Technical Data Relay output No Current Ttransformer 5-10000 Ampere No Directly Current Ttransformer 2-100 Ampere Ok Over Current Can Be Set No Under Current Can Be Set No DEMAND No RS485 – MODBUS RTU RS485, Modbus – Rtu
10+1

DAK-72 Direct AC Ampermeter

Read more

The device can be used in electrical panels, laboratories, and test devices. Withthe assistance of a current transformer, it measures the AC passingthrough the system in terms of Amper unite. If the current exceeds the adjusted current then the alarm led started to blink after the the adjustedtime delay changes the output position.When the current exceeds the adjusted current value the device starts tocount for the adjusted delay time and after that, it opens its output contacts.After energizing the device, a “dA -b “ message appears on its screen for 2 seconds and then it starts to show the current value.

■ The current transformer ratio can be adjusted between 5/5 and 10000/5 using the touch buttons on the front panel of the device.

■ Stores the maximum demand value and the peak value on its memory and keeps these values even if the energy supply goes off.

■ When the measured value of the seconder current reaches 5,1 A, “ OvEr” the message starts to flash on the screen to warn the user that the value of the current exceeded the limit values.

3+1

DAM-B-96 AC Universal Ampermeter

Read more
General Informations  The device can be used in electrical panels, laboratories, and test devices. With the assistance of a current transformer, it measures the AC passing through the system in terms of the Amper unit. When the current exceeds the adjusted
6+1

DAM-C-72 AC Universal Ampermeter

Read more